|
| |
Product Classification : Can Making
|
|
CEBT-100 Buckle Tester for Can and End
|
The ¡°Canneed CEBT-100 Buckle Tester for Can and end¡± determines the exact pressure at which the Can and End begins to buckle. With 4 measuring mode:
|
|
|
BDG-100 Bottom Depth Gauge
|
|
The CanNeed "BDG-100 Bottom Depth Gauge" is a Digital gauges for measuring Bottom depth parameters of beverage cans. Please indicate the can diameter when ordering.
|
|
|
CSG-A Countersink Gauge
|
|
The CanNeed "CSG-A Countersink Gauge (digital)" is a Digital gauges for measuring Countersink depth parameters (the depth of beader of can).
|
|
|
IDG-100 & IDG-200 Can Internal Diameter Gauge
|
This unit serves for quickly checking the Internal Diameter of can. It is equipped with a calibration piece.
IDG-100 is for small diameter cans, Cans dia. 52-100 mm (only measure one type can)
IDG-200 is for large diameter cans, Cans dia. :80-260 mm (only measure one type can)
|
|
|
AMG-300 Aerosol Measuring Gauge
|
|
Measures 6 characteristics in 1 compact Gauge
AMG-300 Aerosol Measuring Gauge is a Convenient Gauge for Aerosol Cans, it can Measures 6 characteristics in 1 compact Gauge. measures the following characteristics:
1) Can Height over all (E)
2) Can Height over the seams (D)
3) Can height between the seams (F)
4) Top Outside Diameter (K),
5) Top seam Outside Diameter
6) Bottom seam Outside Diameter
|
|
|
ELT-100 Leak Tester for End
|
The "Canneed model ELT-100 Leak Tester for End "is used to determine the pressure at which ends buckle. This tester is also used to test for pin hole leaks in the tab score and rivet area.
The ELT-100 applies high pressure air to the product side of and end until the end fails. Leaking spots are made visible by revealing bubbles in the water bath. The failure of an end occurs either when the end buckles or when it starts leaking, leakage is generally caused by faulty scores or rivets.
|
|
|
Seam Sight(TM) Full Automatic Seam Monitor(V3)
|
The Seam SightTM (V3) Full Automatic Seam Monitor is a compact measuring system for quick and accurate automatic seam measurements and storing of seam images.
The seam is positioned in front of the camera and is digitised by the computer.
In less than 1 second the Seam Sight (TM) software offers a measurement. The seam length, body hook, end hook, actual overlap, percentage overlap; seam gap, seam thickness and body hook butting% are measured. At the end of the measurement an evaluated seam appears including dimension lines and measured values. This may be stored in computer or printed out on a laserprinter. The values can be stored in a Excel file and are displayed in on-screen if values are within specs.
|
|
|
STR-100A Seam Stripper
|
|
The automatic STR-100A Seam Stripper is a sensible, affordable, teardown method to prepare the double seam teardown analysis. One fast, safe teardown operation without damaging or distorting the cover hook. Reduce teardown time for more frequent inspections. Tooling quick change in few seconds. Models are available for most common can sizes of beverage, food, and aerosol cans. When ordering, the end diameter and can height must be specified so that the appropriate change parts are included. Efficient cut and strip both aluminium and steel cans in a single motion. 10 seconds per can. Eliminates the repetitious actions by hand .
|
|
|
Seam Sight(TM) 3B Portable Full Automatic Seam Monitor
|
|
The CanNeed "Seam Sight 3B Portable Full Automatic Seam Monitor" is so small and portable to work with a laptop. It was packed with the CSS-P2 into a suitcase, specially designed for those who always on business trip.
|
|
|
CTG-4000 Wet Film and Coating Thickness
|
Application:
1. Test wet film and coating thickness,both save time and improve quality
2. Test both single layer and multilayer coating
3. Adopt non-contact optical technique,suitable for research,quality control and on-line control.
4. Can be used in Solar energe,optical coating,foods package,metal package field.Improve the quality by appearance,adhesion,resistant to corrosion and fricton,as well as scratch.
|
|
|
DHG-300 Digital Can Height Gauges
|
|
The "DHG-300 Digital Can Height Gauge" can be used to measure the height of beverage, food, and aerosol cans. The gauges can be connected to a computer or SPC system via the adapter and cable.
|
|
|
CSS-P3 Portable Seam Saw
|
The the CSS-P2 seam saw is so small and portable. It was packed with "Seam Sight 3B Portable Full Automatic Seam Monitor" into a suitcase, specially designed for those who always on business trip.
CanNeed ¡°CSS-P2 Portable seam saw¡± is a special seam circular saw with double cut for can double seam inspections. The CSS-P2 was specially designed for 2- and 3-piece cans. Also aerosol-cans may be sawed with this saw. The nitrated blades achieve a very plain cut surface. The seam image on automatic seam measuring systems gets thereby very clear and improves measurement speed and reliability.
|
|
|
DHG-300 Digital Can Height Gauge
|
|
The CanNeed "DHG-300 Digital Can Height Gauge" can be used to measure the height of beverage, food, and aerosol cans. The gauges can be connected to a computer or SPC system via the adapter and cable.
|
|
|
ZME-1220 Digital End Blank Gauge for Scroll Cut
|
ZME-1220 is to test the following items of the end blank:
1) Length
2) Parallelism
3) Perpendicularity (angle)
4) Reference points
* Simple operation with the help of a incremental ruler/ fine measuring gauge combination and digital indicators
* Accurate, repeatable, user-independent results
* Continuously displaying readings
|
|
|
STG-200-D Seam Thickness Gauge (Digital)
|
|
The CanNeed ¡°STG-200-D Seam thickness gauge (Digital)¡± is used to measure the Seam thickness of cans. With measure angle compensation. The center measure point can be adjusted. Cans can be auto-positioned in the center easily during measuring. With the Mitutoyo 0.01mm Resolution Digital Indicator.
|
|
|
PNR-C100 Pressure No Return Tester for Cans on Bottom
|
|
The CanNeed "PNR-C100 Pressure No Return Tester for Cans on Bottom" can measure the PNR value (Plastic Deformation) and the buckle value of the can bottom. During the whole pressurization process, use the micrometer to track and measure the deformation amount, generate the curve through the software and analyze the correlation between pressure and deformation amount of the can bottom.
|
|
|
CTG-310 Coating Thickness Gauge
|
|
CanNeed-CTG-310 Coating Thickness Gauge is used to test the coating thickness(coating weight per unit area, g/m2). When equipped with ¡°Hover Probe¡±, it can measure the coating thickness of plate sheets. When equipped with can body testing clamp, it can test the coating thickness of can body.
Use standard coating plate (sample with known weight, g/m2) calibration equipment to test different
types of coatings. Test result and coating type number will display on the screen and the data will be output to PC with RS232.
|
|
|
VRM-4C Video Rivet Monitor
|
|
The CanNeed VRM-4C Video Rivet Monitor is a video camera system to observe and evaluate the rivet's profile images of the ends. The end is cutting through the rivet by the low speed saw LSS-100, the rivet is positioned manually at front of the camera. The rivet profile's images are displaying on the screen. It also can be used with a PC to be a compact measuring system. Within VRM Image Archive Software, the computer offers a measurement. This should be sorted in the computer or printed out on a laserprinter.
|
|
|
CanNeed-SM-24 Electric Belt Drive Seamer
|
The CanNeed "SM-24 Electric Belt Drive Seamer" (Desktop model) enables the users to do more lab tests. Such as, adjusting some technique, enhancing the products quality, test the empty cans and free ends, to insert a temperature logger into a can before running a temperature monitoring.
It is much more convenient for those lab tests, fast, easy and high efficiency
|
|
|
CSM-207 Can Seam Micrometers
|
CanNeed CSM series Can Seam Micrometers are use for measuring the seam thickness and length. The fine tuning function helps to avoid the deviation caused by over rotation.
CSM-208 is applicable to measure the seam thickness and length of flat bottom straight wall cans.
CSM-207 is applicable to measure the seam thickness and length of aerosol cans and necked-in cans.
|
|
|
EPS-100 End Profile Systems
|
|
The CanNeed ¡°EPS-100 End Profile System¡± is used to measure the end dimensions. It is with excellent
performance by adopting precise optics measuring technology, measuring the end dimensions precisely.The inaccuracy of end dimensions usually cause to such double seam defects as fault sealing, bearing
cover and false sealing and so on. It is hard to measure the profile dimensions of ends without EPS-100.
|
|
|
LSS-100 Low Speed Saw
|
|
The "Canneed LSS-100 Low Speed Saw" is for cut the End rivet to observe and evaluate the rivet profile images of ends. It work with the "Canneed VRM 3A Video Rivet monitor".
The end is cut through the rivet by the LSS-100 Low Speed Saw, the rivet is positioned manually in front of the camera. The rivet profile images display on the display.
|
|
|
DER-400 Digital Enamel Rater
|
|
The CanNeed DER-400 Digital Enamel Rater is the industry standard. The new CanNeed Enamel Rater DER-400 instrument test the coverage of the enamel coating inside food and beverage cans, aerosol-cans and also different kinds of ends. It displays an index of the amount of metal exposed by incomplete enamel coverage on a clear, easily read digital LED.
|
|
|
CAN-10774 Planer and Shaper Pin Height Gauge
|
|
The Pin Height Gauge is commonly used in the initial setup of the seamer to ensure double seaming performance and air removal.
|
|
|
SLG-D Seam length gauge(digital)
|
|
The Canneed SLG-D Seam length gauge(digital) can be used to measure Seam length (Seam height).
Can is positoned by standing up during measuring.
With the Mitutoyo 0.01mm Resolution Digital Indicator.
If you purchase the adapter and cable,
the instrument can communicate with a computer.
|
|
|
CSM-208, CSM-207 Can Seam Micrometers (Fine tuning)
|
The CanNeed CSM series Can Seam Micrometers are use for measuring the seam thickness and length. The fine tuning function helps to avoid the deviation caused by over rotation.
CSM-208 is applicable to measure the seam thickness and length of flat bottom straight wall cans.
CSM-207 is applicable to measure the seam thickness and length of aerosol cans and necked-in cans.
|
|
|
CND-TRK-300 Oven Temperature Logger
|
|
The CanNeed CND-TRK-300 Oven Temperature Trackeris a professional oven temperature curve inspection system for the coating industry, it is including the data logger, heat insulation case, software (Chinese / English) and thermocouples."CND-TRK-300 Oven Temperature Tracker" is use to pass through the oven with the solidifying products, and record down the real temperature during the process.
|
|
|
CAN-1050 Can Closing Force Gauges
|
"CAN-1050 Can Closing Force Gauge" is for measuring the force of seaming head of the seaming machine. Advantages:
1. Deduct the scrap rate of the production
2. Shorten the adjusting time, improved production efficiency.
3. Improved the seam quality
|
|
|
CLT-100 Leak Tester for Can
|
The Canneed "CLT-100 Leak Tester for can" is used for checking the leakage of 3-piece cans in a water bath. It can test one can in each test.
The test procedure is performed semi-automatically and the CLT-100 is suitable for different sizes of round 3-piece cans.
|
|
|
IDG-100 Can Internal Diameter Gauge
|
IDG-100, IDG-200 & IDG-300 Can Internal Diameter Gauge
This unit serves for quickly checking the Internal Diameter of can. It is supply with a calibration piece.
IDG-100 is for small diameter cans, Cans dia. 52-100 mm (only measure one type can)
IDG-200 is for large diameter cans, Cans dia. :80-260 mm (only measure one type can)
IDG-300 is compatible for two (2) or three (3) sizes of cans.
|
|
"If you can not find the product you need, please contact us or leave a message."
|
|
