|
| |
Product Classification : All Products
|
|
PTT-300 POP & TEAR TESTER
|
|
The CanNeed "PTT-300 Pop & Tear Tester" was developed for testing different kinds of easy open ends.
Applicable to 7 different types of ends: RP / SOT / EO / OVAL / FSE / SNAP and ALUFIX.
Adopted 5 different testing modes: RP / SOT / EO / OVAL and SNAP.
Operators just need to hook the ring and press "test" button, then the PTT-300 will do the test automatically. During the testing process, the microprocessor will monitor and record the max. Pop and Tear force. With different sizes of the clamps, it is able to test different sizes of ends.
|
|
|
CanNeed-IDG-100/200/300 Can Internal Diameter Gauge
|
|
The “CanNeed-IDG-100 Internal Diameter of Can” is used to measure the internal diameter of small cans, such as 200, 202, 206, 209.
The “CanNeed-IDG-200 Internal Diameter of Can” is used to measure the internal diameter of larger cans. According to clients’ request, CanNeed-IDG-200 can be made to measure 2 to 3 different sizes of cans at the most at the same time. Note: The difference between the internal diameters of the two cans must be over 10mm.
When placing the order, please indicate the internal diameters of the cans, such as 202 neck-in cans, 206 neck-in cans.
With the Mitutoyo 0.01mm resolution digital indicator.
If purchased the adapter and cable, the gauge can be connected to a computer or SPC system for data collection.
|
|
|
FHS-100 Fill Height Syringe
|
Used to adjust water level in a bottle to a pre-determined fill height.
For checking content of bottle using the fill height Syringe accurately and quickly.
|
|
|
ZM-370-D, ZM-570-D, ZM-920-D, ZM-1220-D Digital Body Blank Gauge
|
|
The “Digital Body Blank Gauge CanNeed-ZM-370-D,CanNeed-ZM-570-D,CanNeed-ZM-920-D” are made for the quality control of can body blanks.
|
|
|
CanNeed-FWG-100-d CanNeed-FWG-100-d, CanNeed-FWG-200-d, CanNeed-FWG-300-d Flange Width Gauge (digital)
|
|
The “CanNeed-FWG-100-d, CanNeed-FWG-200-d, CanNeed-FWG-300-d Flange Width Gauge” is used to measure the flange width of empty cans. Reliable design, invariableness measuring pressure and measuring angle which enable the inexperienced operators can also perform the measurementaccurately. Auto aligning the center of can body, applicable for different types of cans.
If purchased the adapter and cable, the gauges can be connected to a computer or SPC system for data collection, avoiding the manual recording and personal error.
|
|
|
CanNeed-PTG-100 Digital Plate Thickness Gauge
|
This unit serves for quickly checking the thickness of plates. The sample is presented vertically in this version. Equipped with the Mitutoyo 0.001mm Resolution Digital Indicator.
If purchased the adapter and cable, the gauge can be connected to a computer or SPC system for data collection.
|
|
|
CDG-100 Curl Diameter Gauge
|
The CanNeed "CDG-100 Curl Diameter Gauge" is a Digital gauges for measuring Curl Diameter of ends. Equipped with calibration piece. With the Mitutoyo 0.01mm Resolution Digital Indicator.
If purchased the adapter and cable, the gauge can be connected to a computer or SPC system for data collection.
|
|
|
WOM 4C Welding Overlap Monitor
|
|
The CanNeed “WOM 3A Welding Overlap Monitor” is used to measure the length and thickness of side seam welding overlap. It’s equipped with the most advanced optical system and Golden LensTM, which ensured the high image definition.
|
|
|
CanNeed-IDG-100/200/300 Can Internal Diameter Gauge
|
The “CanNeed-IDG-100 Internal Diameter of Can” is used to measure the internal diameter of small cans, such as 200, 202, 206, 209.
The “CanNeed-IDG-200 Internal Diameter of Can” is used to measure the internal diameter of larger cans. According to clients’ request, CanNeed-IDG-200 can be made to measure 2 to 3 different sizes of cans at the most at the same time. Note: The difference between the internal diameters of the two cans must be over 10mm.
When placing the order, please indicate the internal diameters of the cans, such as 202 neck-in cans, 206 neck-in cans.
With the Mitutoyo 0.01mm resolution digital indicator.
If purchased the adapter and cable, the gauge can be connected to a computer or SPC system for data collection.
|
|
|
|
CDG-100 Curl Diameter Gauge
|
The CanNeed "CDG-100 Curl Diameter Gauge" is a Digital gauges for measuring Curl Diameter of ends. Equipped with calibration piece. With the Mitutoyo 0.01mm Resolution Digital Indicator.
If purchased the adapter and cable, the gauge can be connected to a computer or SPC system for data collection.
|
|
|
MaltSort Laboratory Malt Sieving Device
|
The “MaltSort Laboratory Malt Sieving Device” base on the size of barley and malt to evaluate its maturity (plumpness), recommended by the EMC committee, specially developed for barley classification. Three types of fine brass strainer: 2.2mm, 2.5mm, 2.8mm.
The “MaltSort Laboratory Malt Sieving Device” is use for classifying the malt and other corn in labs, in the beer factories, it is mainly use for evaluating the brewing barley. The working sample weight is 100g, multiple sieving can be done within a very short time and no need any dismantlement and cleaning after the sieving. The device consists of the shaking device, timer.
|
|
|
CanNeed-WWT-100 Welding Line Outstretched Tester
|
|
The “CanNeed-WWT-100 Welding line outstretched tester” is used to test the flange point welding integrality of 3-pieces cans.
How to test: Place a sample can body on the corresponding plug, handle piston valve. And the cylinder drives the board to press the can body. Stop when the flange os curled about 10 mm. Then loosen the piston valve, take the can body out to check if there is any breaches. Mark down the result.
|
|
|
|
WOM 4C Welding Overlap Monitor
|
|
The CanNeed “WOM 3A Welding Overlap Monitor” is used to measure the length and thickness of side seam welding overlap. It’s equipped with the most advanced optical system and Golden LensTM, which ensured the high image definition.
|
|
|
CDS-10 Can dissect saw
|
Give up the old method for dissecting cans, to observe the can interior has become so easy and clear.
The “CDS-10 Can Dissect Saw” was specially designed to cut the can body into two axially, so that to observe the situation of corrosion or lacquer scale off.
|
|
|
CanNeed-WWT-100 Welding Line Outstretched Tester
|
|
The “CanNeed-WWT-100 Welding line outstretched tester” is used to test the flange point welding integrality of 3-pieces cans.
How to test: Place a sample can body on the corresponding plug, handle piston valve. And the cylinder drives the board to press the can body. Stop when the flange os curled about 10 mm. Then loosen the piston valve, take the can body out to check if there is any breaches. Mark down the result.
|
|
|
CanNeed-WWP-100 Welding Seam Ball Press Tester
|
|
The “CanNeed-WWP-100 Welding Seam Ball Press Tester” is used to test the welding seam quality, including the welding seam strength and continuity of 3-piece cans.
Testing Method: place the empty cans to the clamp, align the welding seam with the ball, and then tightly press the can. The cylinder pushes the ball to slide along the welding seam. Next, take the can out to check if there are any breaches.
|
|
|
CanNeed-BDD-200A Bead Depth Gauge
|
CanNeed-BDD-200A Bead Depth Gauge is for measuring the bead depth of the can body, with the special designed end measuring holder, end bead depth can also be measured. The fine designed can holder, which ensures the cans keep still during the measuring, and the results are more accuracy.
|
|
|
AXL-4000 Axial Load Tester
|
|
The “CanNeed AXL-4000 Axial Load Tester” measures the axial force resistance of beverage cans in Newton. The can is placed in a support and gradually forced upwards against the pressure plate. The space between the support and the top plate can be altered with spacers. The can crashes after the peak force has been applied that the can is capable of resisting. The maximum value can now be read in the display
|
|
|
PDG-d Plane depth Gauge for Canned Food and Beverage
|
|
The “PDG-d Plane depth Gauge (Digital)” is for measuring the bottom end depth of the cans. The measuring base would be subject to the sample size, so please indicated the end size when purchasing.
|
|
|
CanNeed-DHG-300 Digital Can Height Gauge
|
|
The CanNeed "DHG-300 Digital Can Height Gauge" can be used to measure the height of beverage, food, and aerosol cans. The gauges can be connected to a computer or SPC system via the adapter and cable.
|
|
|
FWG-100-D, FWG-200-D, FWG-300-D Flange Width Gauge
|
|
The “CanNeed-FWG-100-d, CanNeed-FWG-200-d, CanNeed-FWG-300-d Flange Width Gauge (digital)” is used to measure the flange width of empty cans. Reliable design, invariableness measuring pressure and measuring angle which enable the inexperienced operators can also perform the measurement accurately. Auto aligning the center of can body, applicable for different types of cans.
If purchased the adapter and cable, the gauges can be connected to a computer or SPC system for data collection, avoiding the manual recording and personal error.
|
|
|
CanNeed-SM-24 Electric Belt Drive Seamer
|
Canneed “SM- 24 Electric Belt Drive Seamer” (Desktop model) enables the users to do more lab tests. Such as, adjusting some technique, enhancing the products quality, test the empty cans and free ends, to insert a temperature logger into a can before running a temperature monitoring.
It is much more convenient for those lab tests, fast, easy and high efficiency
|
|
|
CanNeed-AXL-10000 Axial Load Tester
|
|
The CanNeed “AXL-10000 Axial Load Tester” measures the axial force resistance of food cans in Newton. The can is placed in a support and gradually forced upwards against the pressure plate. The space between the support and the top plate can be altered with spacers. The can crashes after the peak force has been applied that the can is capable of resisting. The maximum value can now be read in the display
|
|
|
VSM 6A Automatic Seam Monitor
|
The " VSM 6A Automatic Seam Monitor " is a compact measuring system
for quick and accurate automatic seam measurements and storing of seam images.
The seam length, body hook, end hook, actual overlap, percentage overlap;
seam gap, seam thickness and body hook butting% are measured.
The values can be stored in a Excel file and are displayed in on-screen if values are within specs.
Seam image can be printed, stored!
|
|
|
CanNeed-PTG-100 Digital Plate Thickness Gauge
|
This unit serves for quickly checking the thickness of plates. The sample is presented vertically in this version. Equipped with the Mitutoyo 0.001mm Resolution Digital Indicator.
If purchased the adapter and cable, the gauge can be connected to a computer or SPC system for data collection.
|
|
|
CanNeed-CLT-600 Leak Tester for can
|
|
CanNeed-CLT-600 Leak Tester for can is used for checking the leakage of 3-pc can XE "3-piece can" s in a water bath. It can test six cans in each test.
|
|
|
STG-200-d Seam Thickness Gauge(digital)
|
the STG-200-d Seam thickness gauge can be used to measure Seam thickness.
With measure angle compensation. The center mesure point can be adjusted.
Cans can be auto- positoned in the center easily during measuring .
With the Mitutoyo 0.01mm Resolution Digital Indicator.
If you purchase the adapter and cable, the instrument can communicate with a computer.
|
|
|
NIPPER
|
|
A convenient, all-purpose hand tool used for hand teardown of can seams. Vinyl coated hand grips, jaw width is 1”, overall length is 6”
|
|
|
CanNeed-CAN-125B Pasteurization Temperature Monitor (PU Monitor)
|
|
CanNeed-CAN-125B Pasteurization Temperature Monitor is used to measure the temperature in bottles or cans ,also water temperature during sterilizing process,caculate Pu value,and temperature curve can display on PC or print out with a printer.
CanNeed-CAN-125B PU Monitor record and store the temperature data of the whole sterilizing process,caculate the total PU value,king PU value(PU value that obtained when temperature is above 60℃), max.wine temperature,max.water temperature,runtime and the runtime of the two max.temperature.Users can define the sampling frequency of the monitoring.The powerful professional software CND-LogSee can print the report and curve,save data as excel files and transfter the data to those computers which have not installed the CND-LogSee software.
|
|
|
CIC
|
|
CIC
|
|
"If you can not find the product you need, please contact us or leave a message."
|
|
